12 pack of 1.5 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The diameter size of each Lead Flashing Jack is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration. Tru-Pitch Lead Roof Flashing Jack assemblies for adjustment to most roof slope conditions. Each flashing includes lead burned seams - Not Soldered! Lead Flashing Jacks are sold in boxes of 12, 6 or 3 Lead Flashing Jacks per box depending on the diameter of flashing in the box. Custom Lead Flashings can be made to order. Specify roof slope for any pitch roof condition and the diameter needed. Note: The National Roofing Contractor Association (NRCA), and most major roof system manufacturers, specify the use of Lead Flashing Jacks in order to qualify flat roofs for extended year manufacture guaranteed roof systems. (NDL Roof Systems) An added bonus: Unlike steel or other metal flashings jacks, it is not necessary to use nails to fasten Lead Flashing Jacks to a roof deck when installed into a built up roofing system (Flat Roof Only). Just press the Lead Flashing Jack into a bead of plastic cement, strip the flashing in, and then finish the roof installation. 1 or 2 piece split lead flashings available for roof penetrations that require fitting. |
|
| 12 pack of 1.5 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The 1.5 inch diameter size is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration |
|
|
| 12 pack of 2.0 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The 2.0 inch diameter size is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration |
|
|
| 6 pack of 3.0 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The 3.0 inch diameter size is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration |
|
|
| 6 pack of 4.0 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The 4.0 inch diameter size is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration |
|
|
| 3 pack of 5.0 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The 5.0 inch diameter size is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration |
|
|
| 3 pack of 5.0 inch square base Lead Pipe Flashing Jacks. Each flashing has a 10 inch high rise cylinder, and a 10 inch square skirt size. For use on Flat or Slope roof applications. These are classified as "Tru-Pitch” Lead Flashing Jacks. The base of the Lead Flashing Riser cone is constructed to allow the Lead Flashing to adjust to minor pitch adjustments. Note: The 5.0 inch diameter size is determined by the inside diameter of the penetration pipe. The Out Side (OD) diameter of this flashing will be larger size to allow the flashing jack to slide over the penetration |
|
|
|
|